FREE SHIPPING IN ITALY FOR ORDERS OVER €150.00 VAT INCLUDED
NEWSLETTER CONTACT US FAQ

Gianneschi Pumps and Blowers

Pumps, pressure tanks, electric fans and original spare parts for boating

Technofluid is the official Gianneschi dealer for Sicily: electric pumps, pressure tanks for fresh water, bilge and fire pumps, engine room fans, boilers and original spare parts, with technical support to find the right code.

  • Official dealer Gianneschi Pumps and Blowers
  • 240 articoli a catalogo
  • Free shipping from €150
  • Pickup in Barcellona P.G. (ME)

Photograph the label with the code: we will tell you the right part.

Sort by:

Gianneschi: Italian pumps and electric fans for boating

Gianneschi Pumps and Blowers is an Italian company from Camaiore (Lucca), active since 1969, designing and producing pumps, pressure tanks, electric fans and boilers for pleasure boats, yachts and work vehicles. At Technofluid you find the range for pleasure boats and original spare parts, sold by an official dealer with technical support.

If you already have a Gianneschi pressure tank or pump on board, replacing or overhauling it with the same brand means finding familiar fittings, sizes and spare parts, without modifying the system.

Gianneschi pressure tanks for onboard fresh water

The pressure tank is the unit that pressurizes the fresh water system: it draws from the tank and sends water to taps, showers and toilets when you open them. A Gianneschi pressure tank unit includes electric pump, pressure control system (pressure switch or Control Press) and, depending on the model, a water tank that stabilizes the pressure and prevents continuous pump starts.

The main families available from Technofluid are Ecoinox, Ecojet, Jet and Idrojet, in 12 V and 24 V DC versions or 230 V and 230/400 V for boats with generator or dock connection.

How to choose the right pressure system

BoatTypical usesRecommended rangeAlimentazione
Up to about 10 m1 bathroom, kitchen, stern showerEcoinox 1/15, Ecojet 112 V or 24 V DC
From 10 to 15 m2 bathrooms, kitchen, outdoor showerEcoinox 2/15, Ecojet 224 V DC or 230 V
Over 15 mMultiple bathrooms and simultaneous usesJet 4B, Idrojet 3 B24 V DC, 230 V or 230/400 V

General guidelines: the final choice depends on required flow rate, pipe length, and onboard voltage. If you are replacing an existing pressure system, send us a photo of the label with the code and we will indicate the equivalent model.

Before ordering, check three things: the system voltage (12 V or 24 V; a 24 V pressure system does not work on a 12 V system), the available space in bilge or in locker and the type of connections of the pipes.

Gianneschi Pumps: bilge, fire-fighting, seawater and diesel

In addition to pressure tanks, Gianneschi produces electric pumps for onboard services: bilge pumping, fire-fighting, deck washing with seawater, diesel transfer and circulation. The series are distinguished by the operating principle, which determines what they can pump and whether they are self-priming.

SeriesPump typeTypical uses on board
CPSelf-priming liquid ringBilge, deck washing, seawater, general services
MVSelf-priming screw, with rubber rotor and statorBilge, thick or contaminated liquids
CBCentrifugalCirculation, cooling, transfer with positive head
ACBSelf-priming liquid ring, flangedFire-fighting, bilge and ballast on larger vessels
BMASelf-priming double volute, high flowBilge and fire-fighting on yachts and workboats

You can find all pumps for these services in the category Bilge, fire, diesel and sea water. If the bilge pump causes problems, start from the most common fault guide.

Electric fans for the engine room

Gianneschi electric fans are used to ventilate the engine room: they bring fresh air to the engines and generator and expel vapors, an important function especially before starting gasoline engines. The range goes from compact models C series at 12 V and 24 V for pleasure boats up to axial ELL series and ELL/AP at 230 V and 400/690 V for yachts.

Stainless steel boilers and water heaters

Gianneschi boilers heat sanitary water with the electric resistance (from dock or generator) and, in the prepared models, with the exchanger connected to the engine cooling circuit. At Technofluid you will find stainless steel boilers and the most requested spare parts: heaters, biothermostats and sacrificial anodes.

Original Gianneschi spare parts: how to find the right code

Technofluid keeps original spare parts for the main Gianneschi pumps and autoclaves in stock. To be sure to order the compatible part:

  1. Read the label with the code on the pump (the plate on the motor): it shows model, code, and voltage (for example “MV44 G – 01GMV341G – 24 V”).
  2. Search the code in the search bar on the site or open the spare parts category below.
  3. If you have doubts, send us a photo of the pump on WhatsApp, with the label clearly readable: our technicians will indicate the correct spare part before ordering.

Maintenance: signs not to underestimate

Many failures of autoclaves and pumps are solved with an original spare part, without replacing the entire unit. These are the most frequent cases:

The autoclave starts and stops continuously

Usually the expansion tank has lost its precharge or there is a small leak in the system. If the pump starts at wrong pressures, check the pressure switch setting: you can find the procedure in the autoclave pressure switch guide.

Water drips from the pump shaft

It is the typical sign of worn mechanical seal. It must be replaced immediately: water reaching the electric motor shortens its life.

The pump runs but does not suck

Check that there are no air intakes on the suction pipe and inspect the condition of the impeller or stator: if they are hardened or worn, the pump loses its priming ability.

The motor struggles or does not start

In DC pumps, the motor brushes wear out with hours of operation. Also check the electrical connections and the voltage at the terminals.

Why buy Gianneschi from Technofluid

Official dealer for SicilyOriginal Gianneschi products and spare parts.
Technical supportWe help you choose the right model and spare part before purchase.
Shipping throughout ItalyFree for orders over €150 VAT included.
On-site collectionIn Barcellona Pozzo di Gotto (ME), convenient for the ports of Milazzo, the Aeolian Islands, and the Tyrrhenian coast.

Frequently asked questions about Gianneschi

Is Technofluid an official Gianneschi dealer?

Yes, Technofluid is the official Gianneschi dealer for Sicily and sells pumps, autoclaves, electric fans, boilers, and original spare parts online with shipping throughout Italy.

Where are Gianneschi pumps made?

Gianneschi Pumps and Blowers is an Italian company based in Camaiore, in the province of Lucca, active since 1969 in the production of pumps and electric fans for boating.

What is the difference between Ecoinox, Ecojet, and Jet autoclaves?

They are families of autoclave groups with increasing flow rates: Ecoinox and Ecojet are suitable for small and medium boats, Jet and Idrojet for larger boats with more bathrooms and simultaneous users. The choice depends on the number of users, onboard voltage, and available space.

Is a 12 V or 24 V autoclave better?

You don't choose: the autoclave must have the same voltage as the onboard system. Smaller boats generally have 12 V systems, larger ones 24 V; 230 V models are used on boats with generators or dock connections.

How do I find the right spare part for my Gianneschi pump?

Search for the spare part code or pump model in the site's search bar, or send us a photo of the pump with the code label on WhatsApp and we will indicate the compatible spare part.

Can the pressure switch of the Gianneschi autoclave be replaced by oneself?

Yes, the pressure switch is also sold as a single spare part. Before replacing it, it is advisable to check its calibration: a miscalibrated pressure switch causes the pump to start and stop at incorrect pressures.

What is the Gianneschi Control Press?

It is the control device that starts and stops the electric pump based on water demand, replacing the traditional pressure switch. It is also available as a spare part for Gianneschi autoclaves that use it.

When should the mechanical seal be replaced?

When you see water dripping from the pump shaft, or during a complete overhaul. It is advisable to replace it along with the impeller or stator if these are also worn.

How much does shipping cost?

Shipping is free in Italy for orders over €150 VAT included. Alternatively, you can pick up the order at our office in Barcellona Pozzo di Gotto (ME).

Can I get assistance to choose the model?

Yes: call us at 090 738 6877 or write to us on WhatsApp with the boat's characteristics or the pump code to be replaced, and we will recommend the suitable model.

Can't find the Gianneschi model or spare part?

Photograph the label with the code: we will tell you the right part.

We ship worldwide
Secure payments
Quality assurance
Customer service WhatsApp
Scroll to Top